top of page

Trusted San Mateo Sewer Ejector Pump Repair & Installation

We install, repair, and replace sewer ejector pumps in San Mateo for basements, ADUs, and below‑grade bathrooms.

Flexible 0% APR Financing • CSLB #1057926 • Same‑Day Service • CSLB #1057926

Repipe Champions Plumbing and Rooter Inc. — Trusted local pros for sealed systems, vents, and check valves.

California State License Board logo for licensed contractors

Proudly serving Santa Clara and San Mateo Counties

Sewer Ejector Pumps 101 for San Mateo Homeowners

In San Mateo, any bathroom, laundry, or fixture located below the main sewer line needs a sewer ejector pump
to move wastewater up to the building drain. Gravity alone won’t do the job — which is why sealed basins,
properly sized pumps, and venting are so important. Our licensed plumbers design systems that match your
fixture load, lift height, and pipe size, so the pump cycles efficiently without short‑cycling or excessive
noise. We also ensure gas‑tight lids, check valves to prevent backflow, and code‑compliant air venting for
safety. For ADUs and basement remodels in San Mateo, our approach starts with an on‑site assessment. We
confirm clearances, electrical supply, and routing for discharge lines. Then we recommend options — from
rugged cast‑iron pumps to quieter, energy‑efficient models — and explain the trade‑offs in head pressure,
gallons‑per‑minute performance, and durability. If your existing basin is undersized or not vented correctly,
we can retrofit a new sealed basin with an external check valve and a serviceable union for future
maintenance. Every installation ends with a full system test: we run fixtures, verify pump activation, check
valve operation, and confirm air‑tight seals. Older homes in San Mateo sometimes inherit DIY ejector setups
that mix storm water or lack backwater protection. Those shortcuts create odors, premature pump failure, and
even sewer backups. We correct these issues by separating drains correctly, adding cleanouts, and using
schedule‑rated discharge piping. Where appropriate, we’ll perform a camera inspection of downstream lines to
ensure there are no hidden restrictions that would overwork your new pump. Documentation, permits, and
inspection coordination are all part of our service. Reliability matters. We stock service parts, offer 24/7
emergency support, and provide maintenance plans for San Mateo property managers and HOAs. Expect tidy work
areas, careful concrete cutting (when needed), and professional patching. We finish by reviewing operating
tips — like what not to flush, how alarms work, and when to call for service — so your system stays dependable
for years.

Sewer Ejector Pump Installation & Repair | Repipe Champions
Heavy-duty green sewer ejector pump for high-capacity plumbing systems

Top Brands, Proper Sizing, and Reliable Installation for San Mateo

Selecting the right ejector pump for your San Mateo project isn’t just about horsepower. We size by total
dynamic head (vertical lift plus friction losses), expected fixture units, and duty cycle. For homes with
frequent use, we’ll recommend heavy‑duty, cast‑iron pumps with 2‑inch solids handling and thermal protection.
We also discuss basin capacity: larger basins reduce cycling and noise, while sealed lids prevent moisture and
odors. Smart add‑ons like high‑water alarms, battery backup in case of outages, and dedicated circuits enhance
safety and reliability. Our team installs reputable brands and specifies check valves and unions that make
future service simple. We ensure the discharge ties into the building drain at the correct elevation with a
proper wye fitting, not a tee that can create turbulence. Venting is routed per code to prevent trap siphonage
and allow smooth pump operation. After installation, we pressure‑test the discharge, confirm alarm function,
and provide you with labeled shut‑offs and an owner’s guide. For multi‑fixture basements or ADUs in San Mateo,
we’ll design manifolded systems that balance performance and cost. To keep your San Mateo ejector pump
running like new, we recommend periodic checks: test the float switch, listen for unfamiliar noises, and
schedule an inspection if cycles change. Avoid wipes, feminine products, and grease — even ‘flushable’ items
can bind the impeller or float. When repairs are needed, we provide clear estimates, fast turnaround, and
options to upgrade. With 0% APR financing available and CSLB‑licensed work, you get dependable results without
surprises.

bottom of page